Home > Products >  high pressure hose 3/8 dimensions
Email:[email protected]

Leave a Reply

high pressure hose 3/8 dimensions

R2-06 | 3/8" SAE 100R2AT Hydraulic Hose (by the foot): …

3/8" SAE 100R2AT Hydraulic Hose is recommended for hydraulic system service with petroleum and water-base fluids, or general industrial service. Maximum working pressure: 4,785 psi Interchanges with Aeroquip FC212-06, Gates 6G2, Parker 301-6, and

M3K Mega3000 Hose (Gates) - Hoses & Fittings - Mid …

M3K hose has smaller exterior dimensions and significantly tighter bend radius than other SAE 100R1 and 100R2 hose. Reinforcement: Braided, high-tensile steel wire. -4, -5, -6 and -8 sizes are one braid; -10, -12, and -16 sizes are two braid. Temperature

High Pressure Fittings and Tubing | Parker Autoclave …

High and Ultra-High Pressure Fittings, Check Valve, and Tubing (60K & 150K) Fittings Elbows, Tees, Crosses, Couplings, and Bulkheads to 150,000 psi (10342 bar) Parker Autoclave''s high pressure coned and threaded fittings for use with 1/4" to 1" tubing rated to

High Pressure Hydraulic Hose, 1SN, 2SN, 4SP, 4SH, R13 …

Our standard high pressure hydraulic hose 1SN can in -40 C to +100 C, ID 4.8–50.8mm, OD 11.8–64mm, operating pressure 40–250, burst pressure 160–1000 bar.

High Pressure Hose Reel Fixed Base (3/8") – Equip2clean

High pressure hose reel with fixed mounted base, direct hand crank rewind, locking mechanism, full flow swivel joint and short hose tail with 3/8 male screw connector. Designed to take various lengths up to 50m of high pressure hose (hose not included).

Top 6 Best Pressure Washer Hoses in 2020 | …

2020/11/6· There are 3 different measurements of a pressure hose you can select from. They are: ¼ th inch, 5/16 th inch and 3/8 th inch. Your pressure hose’s diameter is critical. So, when it comes to gas and electric pressure washer that are designed for residential appliions, select the 1/4 th inch pressure hose.

Hose Technology - Hansa-Flex

3 Table of contents Standard fittimgs for TE, KP, HD 100 bis HD 400 hoses Hose ferrules Page 118 Metric series Page 127 BSP Page 154 NPT Page 169 JIC Page 170 JIS Page 175 SAE Page 185 ORFS Page 188 Flanges Page 192 French series Page 206 Banjos

Parker High Pressure hydraulic Flanges - Hydraulic and Offshore …

M High pressure hydraulic fl anges M5 alogue 4100-8/UK Methods of connection – Parker 4 bolt fl ange products Connecting tube and hose via a threaded tube/hose end connection: The fl ange adapters provide means of connect- ing tubes or hoses to a 4 bolt

Simpson Armor 3/8 in. x 100 ft. x 4500 PSI Hot & Cold …

Monster Hose 3/8 in. x 100'' x 4500 PSI Cold Water Replacement/Extension Hose Monster hoses are made with a dual-braided Monster hoses are made with a dual-braided construction of steel over polyester and jacketed with translucent polyurethane for high strength, durability. 3/8 in. Male solid x 3/8 in. Male swivel.

Parker High Pressure hydraulic Flanges - Hydraulic and Offshore Supplies | Offshore Supplies | Hydraulic Hose

M High pressure hydraulic fl anges M5 alogue 4100-8/UK Methods of connection – Parker 4 bolt fl ange products Connecting tube and hose via a threaded tube/hose end connection: The fl ange adapters provide means of connect- ing tubes or hoses to a 4 bolt

High quality hoses for the mining industry

3 76 92 3/43 12/174 140 1.500 3 1/8 80 96 3/43 12/174 145 1.700 4 102 119 3/43 12/174 170 3.200 5 127 145 3/43 12/174 200 4.200 6 152 170 3/43 12/174 300 5.400 8 204 224 3/43 12/174 700 9.900 Nominal width ID OD Working pressure Minimum burst

High Pressure Equipment Medium Pressure Valves, Fittings and …

High Pressure Equipment Company has developed a line of Medium Pressure products to assure safe and easy pluing through 20,000 psi. These needle valves, fittings, line filters, check valves, safety heads, rupture discs, anti-vibration gland asselies

Parker High Pressure hydraulic Flanges - Hydraulic and Offshore Supplies | Offshore Supplies | Hydraulic Hose

M High pressure hydraulic fl anges M5 alogue 4100-8/UK Methods of connection – Parker 4 bolt fl ange products Connecting tube and hose via a threaded tube/hose end connection: The fl ange adapters provide means of connect- ing tubes or hoses to a 4 bolt

Hydraulic Hose Fittings Charts - JIC, NPT, SAE, ORFS

Many of these hydraulic hose fitting connections are also able to tolerate high pressure, and still perform very well without being compromised. For more information about the Hydraulic Hose Fitting that will work best in your situation, contact us today for more information.

High Temperature Hose | SAE 100R6 - Fittings | Valves | …

These low pressure hoses form part of a push style hose system, in conjunction with the compatible push fit hose fittings. The fittings are fully reuseable and eliminate the need for swaged ferrules. Due to the synthetic rubber construction and single braid reinforcement, these hoses are suitable for use with water, compressed air, hydraulic oil, fuel, and water glycol hydraulic fluids.

3/8" Custom Rubber Propane Hose Per Foot with Fittings

350 psi max working pressure (high pressure) Black neoprene cover 3/8" I.D. Hoses are made onsite by the foot, choose appropriate fittings, fittings are crimped. Length you choose is the length of the hose not including fittings. Custom hoses are non-returnable.

Hose Size Selection Nomograph – RYCO Hydraulics

To find the bore size for a Pressure Line consistent with a Flow Rate of 100 litres per minute (26 US or 22 Imperial gallons per minute), and a Flow Velocity of 4,5 metres per second (14.8 feet per second), connect Flow Rate to Flow Velocity and read Hose Bore

Hose Fittings | Pressure Washers | Pressure Washer Parts

Hose Fittings Pressure Washers & Parts has a high quality range of Hose Fittings uniquely designed for the use with high pressure washers and cleaners. How to Simply Measure the Size of Your Hose Fittings: Use Vernier Callipers, Ruler, or Tape Measure

High Pressure Fittings and Tubing | Parker Autoclave …

High and Ultra-High Pressure Fittings, Check Valve, and Tubing (60K & 150K) Fittings Elbows, Tees, Crosses, Couplings, and Bulkheads to 150,000 psi (10342 bar) Parker Autoclave''s high pressure coned and threaded fittings for use with 1/4" to 1" tubing rated to

Hose Fittings | Pressure Washers | Pressure Washer Parts

Hose Fittings Pressure Washers & Parts has a high quality range of Hose Fittings uniquely designed for the use with high pressure washers and cleaners. How to Simply Measure the Size of Your Hose Fittings: Use Vernier Callipers, Ruler, or Tape Measure

High Pressure Hose Reel Fixed Base (3/8") – Equip2clean

High pressure hose reel with fixed mounted base, direct hand crank rewind, locking mechanism, full flow swivel joint and short hose tail with 3/8 male screw connector. Designed to take various lengths up to 50m of high pressure hose (hose not included).

AEROQUIP 303 HOSE | Aircraft Spruce

Aeroquip 303 Hose 3/8 5/16 2000.228 303-6 $9.80 Quantity Aeroquip 303 Hose 1/2 13/32 2000.264 303-8 $10.90 Quantity Aeroquip 303 Hose 5/8 1/2 1750.372 303-10 $11.50 Quantity Aeroquip 303 Hose 3/4 5/8 1500.456 303-12 $13.95 Quantity Add to Cart

3/8 Inch Pressure Washer Hoses - Pressure Washers Direct

3/8 Inch Pressure Washer Hose superstore. Huge selection of 3 8 Inch Pressure Washer Hoses. Buy 3/8 Inch Hose Direct and save. Pressure-Pro R1 200-Foot (3/8") 4000 PSI High Pressure Hose w/ Quick Connectors (Hot / Cold Water) Model: AHS245 2%

Hydraulic Hose, Industrial Hose, Metal Hose, erhose, …

Online suppliers of Gas,Solar,Pluing,Hydraulic Hose and Fittings, and all other fluid power products. Call on 0333 6000 501 - The UK''s Original online Hose Store.Hydraulic Hose & Fittings, Industrial Hose & Fittings, Metal Hoses, Braided Hoses, Gas Hoses

R2-06 | 3/8" SAE 100R2AT Hydraulic Hose (by the foot): …

3/8" SAE 100R2AT Hydraulic Hose is recommended for hydraulic system service with petroleum and water-base fluids, or general industrial service. Maximum working pressure: 4,785 psi Interchanges with Aeroquip FC212-06, Gates 6G2, Parker 301-6, and

R2-06 | 3/8" SAE 100R2AT Hydraulic Hose (by the foot): …

3/8" SAE 100R2AT Hydraulic Hose is recommended for hydraulic system service with petroleum and water-base fluids, or general industrial service. Maximum working pressure: 4,785 psi Interchanges with Aeroquip FC212-06, Gates 6G2, Parker 301-6, and